View previous topic :: View next topic
|
Author |
Message |
Suresh Reddy
New User
Joined: 29 Aug 2012 Posts: 8 Location: India
|
|
|
|
hi,
I am getting following error after installing TWS.
EQQZ066W OPC HAS NOT BEEN ABLE TO DETERMINE THE JES TYPE. JES3 IS ASSUMED.
EQQZ073I OPC HAS RECOGNIZED THAT THIS IS A JES3 SYSTEM WITH
Actually i need JES2 system.I added EXIT7 and EXIT51 modules also.But still facing same error. In the manuals I red that EQQJES2U job will link edit and create load module in sys1.linklib. But when I tried to run EQQJES2U job is failing with SMPPROC not found.
Could any one suggest what will be the datset name which conatain SMPPROC.
Thanks,
Suresh N. |
|
Back to top |
|
|
dbzTHEdinosauer
Global Moderator
Joined: 20 Oct 2006 Posts: 6966 Location: porcelain throne
|
|
Back to top |
|
|
Suresh Reddy
New User
Joined: 29 Aug 2012 Posts: 8 Location: India
|
|
|
|
Thank you for your reply..I have refred the old thred..even I tried $t exit(7),enable command. Still it is not working..command failed with status invalid. |
|
Back to top |
|
|
enrico-sorichetti
Superior Member
Joined: 14 Mar 2007 Posts: 10886 Location: italy
|
|
|
|
Quote: |
I am getting following error after installing TWS. |
most certainly You did not install it(*), it came already installed with Your zOS
what You are doing are just the POST install/integration steps
Quote: |
Could any one suggest what will be the datset name which conatain SMPPROC. |
Your support should know
SMPPROC is the standard/placeholder name for the SMP procedure used to apply maintenance to Your system
(*) in this case You shoukd know the SMP Procedure name used |
|
Back to top |
|
|
PeterHolland
Global Moderator
Joined: 27 Oct 2009 Posts: 2481 Location: Netherlands, Amstelveen
|
|
Back to top |
|
|
Suresh Reddy
New User
Joined: 29 Aug 2012 Posts: 8 Location: India
|
|
|
|
OPCAXIT7:
LOAD(TWSXIT51)
EXIT(51) ROUTINES=TWSENT51,STATUS=ENABLED
I have added above lines to the JES2PARM member..but geeting error while dng IPL TWSXIT51 can be loaded end or cancel |
|
Back to top |
|
|
Suresh Reddy
New User
Joined: 29 Aug 2012 Posts: 8 Location: India
|
|
|
|
My Z/os version is z 1.10 |
|
Back to top |
|
|
enrico-sorichetti
Superior Member
Joined: 14 Mar 2007 Posts: 10886 Location: italy
|
|
|
|
did You run - as per TWS customization instructions - the TWO jobs to build the relevant exits ???
seems not
look at TWS830.SEQQSAMP for the members starting with EQQJES2
and proceed accordingly
if You/Your support were not capable(*) of following the proper costumzation procedures
whining on a forum is just going to be a waste of time for everybody!
(*) the question on SMPPROC puts Your/Your support competence under a very bad light |
|
Back to top |
|
|
Suresh Reddy
New User
Joined: 29 Aug 2012 Posts: 8 Location: India
|
|
|
|
I have run the Jobs and they are completed fine..now it is showing JES2 in EQQMSGLOG..but when I add the job in OPC and it is geeting submitted to MVS and complting fine and status is changning to S in opc but after job compltion status is not changing to C or E accordingly.
Could you please advise. |
|
Back to top |
|
|
PeterHolland
Global Moderator
Joined: 27 Oct 2009 Posts: 2481 Location: Netherlands, Amstelveen
|
|
|
|
Did you recycle OPC ? |
|
Back to top |
|
|
Suresh Reddy
New User
Joined: 29 Aug 2012 Posts: 8 Location: India
|
|
|
|
Yes..I have recycled OPC for several times. |
|
Back to top |
|
|
dick scherrer
Moderator Emeritus
Joined: 23 Nov 2006 Posts: 19243 Location: Inside the Matrix
|
|
|
|
Hello,
What does TWS support have to say? |
|
Back to top |
|
|
enrico-sorichetti
Superior Member
Joined: 14 Mar 2007 Posts: 10886 Location: italy
|
|
Back to top |
|
|
enrico-sorichetti
Superior Member
Joined: 14 Mar 2007 Posts: 10886 Location: italy
|
|
|
|
Quote: |
What does TFS support have to say? |
most probably You meant TWS
Yup, corrected, thanx!
IMO the TS does not have any support,
he is playing by himself with the zOS 1.10 ADCD |
|
Back to top |
|
|
PeterHolland
Global Moderator
Joined: 27 Oct 2009 Posts: 2481 Location: Netherlands, Amstelveen
|
|
|
|
The IBM Tivoli Workload Scheduler for z/OS sample library that was created during installation contains a sample EQQUX007 exit written in assembler language. This sample exit reports batch-job errors to the Information/Management product. |
|
Back to top |
|
|
PeterHolland
Global Moderator
Joined: 27 Oct 2009 Posts: 2481 Location: Netherlands, Amstelveen
|
|
|
|
Is the JCC (job completion checker) started? |
|
Back to top |
|
|
|