View previous topic :: View next topic
|
Author |
Message |
futuredba
New User
Joined: 08 Jan 2006 Posts: 22 Location: Delhi
|
|
|
|
Hi,
My jcl has failed with S013 abend code. The reason code is 'E1' which states that "A magnetic tape data set with a block size greater than 32,760 is being opened for input or output extend processing, but the large block interface is not being used."
What i need to do so that the tape dataset uses large block interface?
Thanks,
Sumit |
|
Back to top |
|
|
Anuj Dhawan
Superior Member
Joined: 22 Apr 2006 Posts: 6250 Location: Mumbai, India
|
|
|
|
Hi,
S013 shuold be accompanied by message IEC141I. Refer to the explanation of message IEC141I for complete information about the task that was ended and for an explanation of the return code or post that here for us to start with. |
|
Back to top |
|
|
dick scherrer
Moderator Emeritus
Joined: 23 Nov 2006 Posts: 19244 Location: Inside the Matrix
|
|
|
|
Hi Anuj,
Quote: |
post that here for us to start with. |
That is what Sumit posted. . .
Sumit,
Please post the complete jcl for the abended step. Also post the complete diagnostic info rather than the bit you quoted. Describe the content of the problem file/volume.
You might also talk with your storage management people and make sure that the file you are trying to read is appropriate for the task at hand. It may be that you are trying to read data stored in a format incompatible with the program trying to read it. |
|
Back to top |
|
|
karz
New User
Joined: 04 Feb 2010 Posts: 39 Location: Mumbai
|
|
|
|
Thanks guys, i encountered this error and got this solved. This is an exceptional case and we all were lookign for the load module and got it compiled again. But the actual problem as mentioned above was with the blksize. |
|
Back to top |
|
|
Anuj Dhawan
Superior Member
Joined: 22 Apr 2006 Posts: 6250 Location: Mumbai, India
|
|
|
|
Good and Thanks for the feedback! |
|
Back to top |
|
|
sai z
New User
Joined: 21 Nov 2015 Posts: 2 Location: india
|
|
|
|
Hi Sumit
Did your issue got resolved S013-E1 ? I am too facing the same issue. Could u please help me get out of this..
Thanks,
Sai |
|
Back to top |
|
|
enrico-sorichetti
Superior Member
Joined: 14 Mar 2007 Posts: 10872 Location: italy
|
|
|
|
the last Sumit' s appearance on the forum was on Fri Dec 05, 2008
The chances of getting a reply from him will be almost inexistent
for the problem in question
look at the messages as suggested AND speak to Your storage support people.
remember also that tailgating to somebody' s else topic to ask about Your problem
is considered bad netiquette |
|
Back to top |
|
|
sai z
New User
Joined: 21 Nov 2015 Posts: 2 Location: india
|
|
|
|
Thanks for the suggestion enrico.
Bad netiquette . When I was registering as a new user into this forum I have seen rule no 2
2. NEVER FORGET TO SEARCH THE FORUMS BEFORE POSTING YOUR QUERIES TO AVOID REPOSTS
Simply followed it.
Thanks,
Sai |
|
Back to top |
|
|
Akatsukami
Global Moderator
Joined: 03 Oct 2009 Posts: 1788 Location: Bloomington, IL
|
|
|
|
The purpose of searching the fora is to determine if your question has already been answered, not to find an ancient, quiescent thread to which to append it.
In any case, even before searching the fora, one should read the fine manual. |
|
Back to top |
|
|
enrico-sorichetti
Superior Member
Joined: 14 Mar 2007 Posts: 10872 Location: italy
|
|
|
|
what rules were You reading ?
not certainly
www.ibmmainframes.com/viewtopic.php?t=12
where it is clearly stated
Quote: |
The Five Rules you must Follow here to confirm your membership:
1. START A NEW TOPIC TO POST YOUR QUERIES.
...
|
and Yes... hacking somebody' s else topic is considered bad manners. |
|
Back to top |
|
|
|