Portal | Manuals | References | Downloads | Info | Programs | JCLs | Master the Mainframes
IBM Mainframe Computers Forums Index
 
Register
 
IBM Mainframe Computers Forums Index Mainframe: Search IBM Mainframe Forum: FAQ Memberlist Usergroups Profile Log in to check your private messages Log in
 

 

Need a cics environment delay of less than 1 second.

 
Post new topic   Reply to topic    IBMMAINFRAMES.com Support Forums -> CICS
View previous topic :: :: View next topic  
Author Message
mgatlin

New User


Joined: 04 Mar 2005
Posts: 2

PostPosted: Fri Mar 04, 2005 12:07 am    Post subject: Need a cics environment delay of less than 1 second.
Reply with quote

In an effort to improve efficiency I need to be able to do a time delay of
100s or 1000s or seconds. The "interval delay" command will not go below
1 second.

Any ideas?
Back to top
View user's profile Send private message

ovreddy

Active User


Joined: 06 Dec 2004
Posts: 211
Location: Keane Inc., Minneapolis USA.

PostPosted: Fri Mar 04, 2005 12:10 pm    Post subject:
Reply with quote

Hi,

As I know it is not possible to delay below 1 second. I think even it is not required in real time. 1 second is not observable. You can get more information and limitations from http://publib.boulder.ibm.com/infocenter/txen/index.jsp?topic=/com.ibm.txseries510.doc/erzhai0032.htm


Bye,
Reddy.
Back to top
View user's profile Send private message
kingofmf

New User


Joined: 02 Mar 2005
Posts: 13
Location: Bangalore

PostPosted: Fri Mar 04, 2005 1:13 pm    Post subject:
Reply with quote

hi,
i had also faced the same problem while tried to animate the output,you can try by inserting some dummy loop of 1000 or 20000 iterations as you needed to do this,but as far as i know there is know built in facility for less than 1 sec delay.
try it,best of luck
Back to top
View user's profile Send private message
mgatlin

New User


Joined: 04 Mar 2005
Posts: 2

PostPosted: Fri Mar 04, 2005 9:32 pm    Post subject: Need a cics environment delay of less than 1 second.
Reply with quote

Thanks for the input on this I appreciate it.

FYI.......I'm now experimenting with repeated accesses of the absolute time feature of CICS which is in milliseconds. I should be able to act upon the passage of time below seconds.
Back to top
View user's profile Send private message
View previous topic :: :: View next topic  
Post new topic   Reply to topic    IBMMAINFRAMES.com Support Forums -> CICS All times are GMT + 6 Hours
Page 1 of 1

 

Search our Forum:

Similar Topics
Topic Author Forum Replies Posted
No new posts INDEPENDENT CICS TS 4.1 MRO REGION UP... Kyle Carroll CICS 0 Wed Dec 14, 2016 6:55 pm
No new posts CICS START AND CANCEL blayek CICS 1 Wed Dec 07, 2016 3:27 am
No new posts How does a called pgm know if its cal... Graeme Westerman COBOL Programming 4 Tue Nov 29, 2016 9:25 pm
No new posts CICS Roll back partially - Need to re... dwijadas CICS 4 Wed Nov 16, 2016 4:30 pm
No new posts CICS NEW SIT PARAMETERS CICS BEHAVIOR... Kyle Carroll CICS 0 Fri Nov 04, 2016 11:55 pm


Facebook
Back to Top
 
Mainframe Wiki | Forum Rules | Bookmarks | Subscriptions | FAQ | Tutorials | Contact Us